Norac UC4+BC+FT2 User Manual

Fast 120’ Passive Roll Installation Manual Spray Height Control System Improving the competitiveness of Industry and Agriculture through Prec

74 INSTALLATION PROCEDURE 4.1 SENSOR INSTALLATION Mounting the sensor bracket to the break-away section of the boom may cause the boom to drop

8Apply a light coating of the supplied Permatex Anti-seize grease to all threaded parts upon installation. Figure 6: Sensor Serial Number Installa

94.2 ROLL SENSOR INSTALLATION Mount the roll sensors to the included roll sensor brackets using the machine screws and nylon lock nuts. (Figure 7)

10 Figure 9: Roll Sensor Mounting with Respect to Sprayer Orientation Figure 10: Roll Sensor Mounting * The boom frame roll sensor does not have

114.2.1 Boom Roll Sensor Mounting The boom roll sensor (E02) must be mounted to the rotating part of the boom. Follow these guidelines and refer t

124.2.3 Inverted Roll Sensor Mounting If desired, the Roll sensor may be mounted inverted, so long as the connector exits towards the right-hand b

134.3 HYDRAULIC INSTALLATION 4.3.1 Valve Mounting 1. On a clean surface remove all plastic plugs from the NORAC hydraulic Valve (V01) (Figure 14)

144.3.2 Hydraulic Plumbing 1. After the NORAC valves are mounted, the hydraulic hoses and fittings can be plumbed. The plumbing for the hydraulic

154.4 ELECTRICAL INSTALLATION Figure 16: Cable Configurations: Rear of the sprayer 1. Route C11 to the rear of the sprayer, in the vicinity of

16 Figure 17: Valve Cable Connections 8. Connect the sensor branch cable (C02) to the 4-pin AMP plug (P4) on C11 (Figure 18). 9. Route the sensor

Printed in Canada Copyright  2005-08 by NORAC Systems International Inc. Reorder P/N: UC4+BC+FT2-INST Rev I (Fast 120’ Passive Roll) NORAC Systems I

174.5 COMPLETING THE FACTORY INSTALL 1. Test the functionality of the original manufacturer’s boom controls. The NORAC Control Panel (Item E01) d

185 END USER INSTALLATION 1. Install the UC4+ Control Panel (E01) in the cab of the sprayer. Mount the panel where it will be clearly visible an

2. Connect the power cable (C10) to the UC4+ Control Panel in the sprayer cab. Ensure that both plugs (P16A and P4) are connected to the panel (Fig

206 ELECTRICAL REFERENCE – CABLE DRAWINGS 6.1 ITEM C02: 44668 – CABLE UC4 SENSOR BRANCH

216.2 ITEM C03: 44656D – CABLE VALVE VARIABLE RATE DT

226.3 ITEM C10: 44650-35 – CABLE POWER GENERIC PULL-TYPE L = 240" (6.10m)

236.4 ITEM C11: 44651-03 – CABLE VALVE EXTENSION GENERIC 365” (9.27m)

246.5 ITEM C12: 44658-73 – CABLE UC4 INTERFACE FAST A&L DT

Canada NORAC Systems International Inc. CALL TOLL FREE: 1-800-667-3921 (306)664-6711 SHIPPING ADDRESS: 3702 Kinnear Place Sas

TABLE OF CONTENTS 1 INTRODUCTION ...

11 INTRODUCTION Congratulations on your purchase of the NORAC UC4+ Spray Height Control system. This system is manufactured with top quality comp

22 GENERAL SYSTEM DESCRIPTION Figure 1 depicts the general system layout of the UC4+ Spray Height Control system. Figure 1: System Components an

33 PARTS LISTS The parts that come with your UC4+ Spray Height Control System are listed in Table 1. The item number on the left side of this ta

4Table 2: 44865-09 - Hydraulics Fittings Kit Item Part Number Name Quantity PictureF02 105588 TEE ADAPTER 4FJXR 4MJT 2F03 104632 TEE ADAPTER 8FJXR 8

5The parts that come with your UC4+ System are shown below in their general installation configuration. Figure 2: UC4+ Spray Height Control Compone

6 Figure 3: Hydraulic Plumbing Schematic